CONNECTIONU USBUSB port to connect to a computerS PC/IOS SOURCESet to PC position when using with VirtualDJM MASTER OUTPUTConnect a pair of amplified speakers using a RCA cable or adapterH HEADPHONES SOCKETConnect your Headphones using a 1/8 " cable or adapter
SHIFT (SECONDARY) ACTIONS SHIFTPress this button down to access secondary actions as described in the SHIFT ACTION column 1 PLAYPlay/pause the loaded TrackPlay/Stutter 2 CUESets current position as Temporary Cue point. Preview track when paused while button is pressed
Jumps and stops to the Cue point when playingJump and stops at the beginning of the Track 3 SYNCMatch BPM and Beat Phase with the opposite deckSmoothly reset Track's Tempo to its original value4 MODEPress and hold this button and then press one of the 8 Pads to select a mode for the Pads. See PadsSet Pads to Touch FX mode. See Pads5 PADSOperation depends on the selected Pads mode. See PadsOperation depends on the selected Pads mode. See Pads6 PARAMETERAdjust the 1st Parameter of the selected Pads modeAdjust the 2nd Parameter (if available) of the selected Pads mode 7 VINYLEnable/disable Vinyl mode. When enabled, use the upper part of the jogwheel to scratch and the outer part to nudge. When disabled, use both the upper and outer part of the jogwheel to nudgeEnable/disable Slip mode. When enabled, several actions such as Hotcues, Loops and scratch will act temporary and when done,Track will resume playback from the position it would have been if the action was never triggered8 KEYLOCKEnable/disable Keylock (Master Tempo). When enabled, changing the Tempo of the loaded Track will not alter its KeyMatch the Key of the loaded Track to the Key value of the other Deck on first press, and reset its Key on 2nd press9 JOGTouch sensitive jogwheel for Scratch (when Vinyl mode is enabled) or Bend (when Vinyl mode is disabled)Fast search (seek) Track 10 PITCHAdjust track's tempo (BPM) 11 FX LEVELAdjust the 1st Parameter (usually Wet/Dry) of the selected Effects from all 3 FX SlotsAdjust the 2nd Parameter of the selected Effects from all 3 FX Slots12 FX1 - FX3 ONEnable/disable the selected Effect of FX Slot 1 to FX Slot 3.Open the Effects drop-down list to select an Effect for FX Slot1 to FX Slot 3. Use the LOOP encoder  to scroll up/down and push the LOOP Encoder  to select and close the Effects list.13 LOOPTurn the encoder (anti)clockwise to half/double the size of the loop.
Push to enable/disable the loop.
When an Effect drop-down selection list is opened (using SHIFT+FX1-3 ON is used), use the encoder to scroll up/down through the Effects list. Push to select the Effect and close the list.When loop is enable, turn the encoder to forward/backwards move the loop in time by 1 beat a step 14 CROSSFADERBlends audio signals from left and right decks 15 VOLUMEAdjust Volume Output for Left and Right deckAdjust Volume Output and and the same time, start Deck when moving from minimum position and stop Track when moving to the minimum position (Fader Start/Stop) 16 PFLSends pre-fader audio signal of the Left/Right Deck to the Headphones channel (for pre-listening) 17 FILTERApply the selected Color FX (by default FILTER) to the Left/Right Deck. When the knob is at center position (12 o'clock), no Color FX is applied. 18 LOADLoad the selected Track from Browser to Left/Right Deck. Double-press to clone the Track from a Deck to the other DeckUnload Track from Left/Right Deck 19 BROWSEScroll through Folders or Tracks
Push to toggle focus between Folders and Songs List.Scroll fast (by +/- 10 Tracks per click.
Push to set focus to Folders list. When in Folders list, expand/collapse sub-folders 20 EQ LOWAdjust the Low Equalizer frequency Band 21 EQ HIGHAdjust the both Mid and High Equalizer frequency Band 22 GAINAdjust the pre-fader output level (Gain) of Left/Right deck 23 MASTER VOLAdjust the Volume of the Master Output 24 CUE MIXBlend in Headphones the signal from the Decks with PFL enabled and the Master Output. 25 CUE VOLAdjust the Volume of the Headphones Output Pads