RANE SEVENTY
for VirtualDJ 8.4 Last Update : June 2020
SETUP
Firmware & Drivers
Firmware: There is no firmware update available at the time this manual was written, but it's a good practice to check for updates at
Rane Dj DownloadsDrivers: Install the latest drivers (for both
Windows and
MacOS X computers) from
Rane Dj DownloadsVirtualDJ Setup
Download and install VirtualDJ from our Downloads Page (in case you have not done already)
Once VirtualDJ is launched, a Login Window will appear. Please login with your preferred method from the ones provided.
A Pro Infinity or a Pro Subscription License is required to fully use the Rane Seventy.
Without any of the above Licenses, the controller will operate for 10 minutes each time you restart VirtualDJ.
Buy a license
A detection window will appear next verifying proper connection with Rane Seventy.
Click on the "Seventy" button in order VirtualDJ to apply the pre-defined audio configuration for your device. Keep in mind that due to the nature of the device, speakers need to be connected to the Master Output of Seventy and the pre-defined audio configuration has to be used.
Make sure you have the top-panel Source selectors to USB-A or USB-B depending on the USB port you connected at the rear panel.
Click to OK.
The unit is now ready to operate. MAPPING
The unit should be visible in the MAPPINGS tab of Config and the “factory default” available/selected from the Mappings drop-down list. The factory default Mapping offers the functions described in this Manual, however those can be adjusted to your needs via VDJ Script actions.
Find more details at
VDJ Pedia AUDIO Setup
The unit has a pre-defined Audio setup and a special button in the AUDIO tab of Config to provide that. Alternative Audio setups can be applied in the same window. See
Advanced Setup for more details.
For further software settings please refer to the
Manuals of VirtualDJ
LAYOUT
The functionality of each button, knob and slider per section (as shown in the image above) will be explained in detail in the next chapters
S SHIFT Hold this button down to access secondary functions of Rane Seventy as described in this manual
A MIXER & EQUALIZERB EFFECTSC BROWSER & LOOP CONTROLSD PADSE REARF FRONT
MIXER , EQUALIZER & OTHER IN/OUT CONTROLS
KEY
ACTION
1 CROSSFADERBlends audio between left and right mixer channels2 VOLUMEAdjust the Volume of each mixer channel.3 CUE CROSSFADERBlend the pre-fader audio signal from Left and Right mixer channels to the Headphones Output. When set to far left, only the Left channel will be heard in Headphones and when set to far right, only the Right channel will be heard to Headphones4 CUE MIXBlends the audio that's being sent on the headphones channel between the headphones signal (far left) and the master output signal (far right).5 CUE LEVELAdjusts the volume of the headphones channel.6 EQ LOWAdjust the low (bass) frequencies of left/right mixer channel.7 EQ MIDAdjust the mid (middle) frequencies of left/right mixer channel.8 EQ HIGHAdjust the high (treble) frequencies of left/right mixer channel.9 LP/HP FILTERApply a Low/High-pass Filter to left/right mixer channel. When centered, no Filter is applied.10 LEVELAdjusts the audio level (gain) of left/right mixer channel.11 SOURCE SELECTSelect the input source of Left/Right mixer channel. Put the switchers to USB A or USB B position for sending Left/Right VirtualDJ Deck to Left/Right mixer channels.12 MAIN LEVELAdjusts the volume of the Master output of the device (connection at the rear panel).13 BOOTH LEVELAdjusts the volume of the Booth output of the device (connection at the rear panel).14 SESSION INAdjusts the volume of the incoming signal on "Session" input on the rear panel of the device.15 SESSION OUTAdjusts the volume of the "Session" output (connection at the rear panel of the device).16 SESSION CUEWhen enabled, sends the signal of the "Session" input to the headphones channel for pre-listening..17 MIC LEVELAdjust the volume of the Microphone 1 input (connection at the rear panel of the device)18 MIC TONEAdjust the tone (single band equalizer) of the Microphone 1 input (connection at the rear panel of the device)19 MIC ONTurn on/off the signal of the Microphone 1 input (connection at the rear panel of the device)20 MIC ECHOApplies an Echo effect on the Microphone 1 input Please note that all these operations are hardware operated, but the movement of some of them will be visible in VirtualDJ GUI.
EFFECT CONTROLS
The Rane Seventy offers the ability to apply Hardware (Flex) and software (VirtualDJ) Effects on left/right mixer channel.
Use the FLEX/SOFTWARE FX button to toggle between the 2 modes. Arm/Select the Effects you wish to trigger via the 6 labeled buttons, then use the latch on/off-temporary switches to apply the armed Effects to left/right mixer channel. All the information about the Effects will be displayed on the LCD of the Rane Seventy.
KEY
ACTION
SHIFT (SECONDARY) ACTION
21 LCDThe Display will show the names of the Effects for Slots 1-3 on both sides (and highlighted if armed), the BPM of Left/Right Decks and the Beats value of the Effect from FX Slot 1. 22 FX SELECTIn Flex FX mode:
Use these buttons to arm/select the Hardware effects you wish to turn on/off. All 6 Hardware Effects - as printed on silkscreen - can be enabled on both mixer channels, but it's a single selection, so only one can be selected/armed and enabled each time.
In Software FX mode:
Use these buttons to arm/select the VirtualDJ Effects you wish to turn on/off. The left 3 buttons represent the 3 VirtualDJ FX slots of Left Deck and can be applied only to Left Deck, while the 3 right buttons represent the 3 VirtualDJ FX Slots of Right deck and can be applied on Right deck only. All 3 Effects per Deck can be armed and enabled at the same time In Flex FX mode:
Enable a mode where the Parameters of the Hardware Effects can be changed
In Software FX mode:
Enable the Selection mode (led will blink). When enabled, use the TIME encoder to select a different Effect on the FX slot that this mode is enabled.
23 FX MODEToggle between Flex FX (Hardware Effects - led lit in blue) and Software FX mode (VirtualDJ Effects - led will be lit in orange). 24 FX ON/LOCKEnable/disable the armed(selected) Effects to Left/Right Mixer Channel. Move the latch switcher down to apply the Effect(s) temporary or move up for toggling. 25 TIMEAdjust the 2nd Parameter of the Effect (usually the Beats Parameter) on Left or Right Deck, depending on the arrow indicator you see on the LCD 26 BEATMove the joystick up/down to increase/decrease the Beats of the Effect on Left or Right Deck, depending on the arrow indicator you see on the LCD
Move the joystick left/right to select which side the BEATS and the Joystick will affect (notice the arrow on the LCD) Move to any direction to access the Utilities/Settings menu of the Device. 27 DEPTHAdjust the 1st Parameter of the Effect (usually the Wet/Dry - Frequency Parameter) on Left/Right Deck 28 TAPManually Tap on tempo to define Track's tempo in case it has not been properly calculated by VirtualDJ Open/close the device Settings/Utilities menu
BROWSER & LOOP CONTROLS
KEY
ACTION
SHIFT (SECONDARY) ACTION
29 SCROLL/LOADScroll through files/folders.
Push to load the selected track to Left/Right Deck Scroll through files/folder.
Push to toggle Browser focus between Songs list and Sideview 30 BACKSets focus to Folders list. If focus is in Folders list, open/close sub-folders 31 LOAD PREPAREAdds the selected track from the Songs list to the Automix list Cycles through the tabs of Sideview (Automix,Sidelist,Karaoke, Sampler and Shortcuts)32 LOOP ON/OFFEnable/disable a Loop of the selected beats size Enables the last triggered loop (reloop)33 LOOP x 1/2Halves the size of the loop Set the Entry (In) point of a manual loop. When in loop, enables the Loop In Adjust mode and a jogwheel can be used to fine-adjust the Loop In point34 LOOP x2Doubles the size of the loop Set the Exit(Out) point of a manual loop. When in loop, enables the Loop Out Adjust mode and a jogwheel can be used to fine-adjust the Loop Out point35 INSTANT DOUBLESClones the track of the Left/Right Deck to Right/Left Deck including it's playing status, position and tempo
Performance Pads
The 8 RGB Pads offer various functions, depending on the selected Pad mode. Each of the 5 Pad mode buttons offers 2 individual modes. Press a pad mode button once to access it's primary mode, and press it again to access it's secondary mode. The modes represent a page of the PADS section on the default VirtualDJ GUI.
KEY
ACTION
SHIFT (SECONDARY) ACTION
36 PAD MODESSelect a mode for he Pads. When a mode is selected, press the same button to select the secondary mode.
Primary modes (1st press): Hotcues, Saved Loops, Loop Roll, Sampler, *Transport
Secondary modes (2nd press) : Cue Loop, Manual Loop,Loop, Sampler Velocity, Slicer 37 PADS8 Performance pads with RGB leds offering different functionality depending on the selected mode. See further details in Pads of VirtualDJ Manual Functionality depending on the selected mode. See further details in Pads of VirtualDJ Manual38 PARAMETERAdjust the 1st Parameter of the selected Pads mode Adjust the 2nd Parameter of the selected Pads mode..* Transport mode
When the Transport mode is selected, a special TRANSPORT 70 page will be selected for Pads, offering basic transport Deck controls. This page will be available only when the Rane Seventy is connected.
REAR PANEL
KEY
ACTION
39 POWER SWITCHTurns ON/OFF the power of the device.
Please make sure that you have made all the necessary connections on the back of the unit before turning it's power ON.40 POWER CONNECTORConnect a standard IEC power cable.41 USB (Type B) PORTSConnect a standard USB cable to connect Rane Seventy with your computer.
You can connect up to two computers by using the two ports of the device (labeled USB A and USB B).
Make sure that you turn the channel CH INPUT SWITCHES at the top panel to the correct USB port for software mixing.42 USB (Type A) PORTSConnect your controller (like Rane Twelve) to use the integrated USB HUB of the device.43 MASTER OUTPUTBalanced XLR Master Output. Connect your amplifier of self-amplified speakers.44 BOOTH OUTPUTBalanced TRS 1/4" Booth Output. Connect your booth/zone amplifier or self-amplified speakers.45 SESSION OUTAdditional RCA unbalanced output useful to chain Rane Seventy with another mixer or to connect an external recorder46 SESSION INRCA Input useful to chain Rane Seventy with another mixer or to add any device that provides a line level output on your mix47 DECK 1/2 AUX INPUTSConnect an auxiliary audio source. The sound of these devices will be routed on channel 1/2 of the mixer.when the Input Source switcher at the top panel is set to AUX.48 DECK 1/2 CD/PH INPUTSConnect your analog gear (like CD Players and Turntables). The sound of these devices will be routed on channel 1/2 of the mixer.
Attention: When you connect a device on the PH/CD RCA plugs make sure that you also switch the PH/CD switch on the appropriate position depending on the device you have connected. Failing to do so may result in heavy distortion or a very weak signal of the analog source.
For DVS (Timecode), set the top-panel Input Source switches to USB49 GROUNDConnect your turntables ground cable (if they offer one).50 MIC 1 INPUTConnect a microphone, or an instrument. When an instrument is connected make sure to turn the LINE/MIC switch to "Line" position.51 MIC 2 INPUTConnect a microphone, or an instrument. When an instrument is connected make sure to turn the LINE/MIC switch to "Line" position.
FRONT PANEL
KEY
ACTION
52 MIC 2 ON/OFFEnables/Disables the microphone 2 input (connection at the rear panel).53 MIC 1 ECHO STRENGTHAdjusts the strength of the echo effect used on microphone input 1.54 MIC 2 VOLUMEAdjust the volume of the microphone 2 input.55 MIC 2 TONEAdjust the tone (single band equalizer) of the microphone 2 input.56 TENSIONAdjusts the tension applied to the Crossfader (smooth/hard feeling)57 CROSSFADER CONTOURAdjusts the contour (slope) of the crossfader.58 DECK 1/2 FADER CONTOURAdjusts the contour of deck 1/2 volume faders.59 CROSSFADER REVERSEReverses the direction of the crossfader.60 DECK 1/2 FADER REVERSEReverses the direction of deck 1/2 volume faders.61 SPLIT CUEWhen enabled, the signal of the mixer channels that are defined from the top-panel CUE fader will be routed to one side of headphones, while the signal of the Master Output will be routed to the other side.62 HEADPHONESConnect your Headphones for prelistening.
ADVANCED SETUP
VirtualDJ is offering DVS (Digital Vinyl System) support for the Rane Seventy. A Pro Infinity license is required. 2 Timecode Inputs are available to control any software decks via Timecode CDs or Vinyls.
Both Mixer Channels can accept LINE (Timecode CDs) or PHONO Sources (Timecode Vinyls) depending on the CD/PH switchers at the rear panel of the unit.
- Connect your Timecode devices at the rear panel of the Rane Seventy
- Open VirtualDJ configuration window and select the AUDIO tab on the left
- Click on the "TIMECODE SIGNAL" button to enable the timecode inputs
- Your sound setup should be like the one shown on the following image:
Rane Seventy Sound Configuration with Timecode Inputs Configured
- Click on "Apply" button
- Click on the TIMECODE icon on the left side of configuration window.
- Press PLAY on your timecode CD or Vinyl device and VirtualDJ will automatically detect your Timecode type and make the appropriate adjustments for best performance.
- Click on the ON buttons from the TIMECODE panels of the Default Skin (in the SCRATCH center panel) to enable the Timecode control to any of the 4 software decks.
- Press PLAY on your timecode CD or Vinyl device and VirtualDJ will automatically detect your Timecode type and make the appropriate adjustments for best performance.
- Press the CALIBRATE button if for any reason the signal is not detected (possibly due to reversed phase connections).
The Rane Seventy has two USB ports, allowing simultaneous connection of two computers. Each port is completely independent. It is possible to run VirtualDJ on one computer and any other DJ-software on the other, Mac or PC.
How to:
- Connect the 2nd computer to the unused USB port on the Seventy.
- Switch the Input Source of the non-playing mixer channel to the USB source of the 2nd computer.
- Play a track on this deck and mix it when ready – you ll now have audio from both computers during the mix.
- Fade out the audio playing from the 1st computer to the audio playing from the 2nd one.
- When only audio from the 2nd computer is left in the mix, remove the first computer.
- Assign the Input Source for the remaining free mixer channel to the 2nd computer and keep mixing.
The Rane Seventy has a
dedicated Input to record your Main Mix. VirtualDJ has pre-configured this input for recording, thus no special setting is required in order to record your mix (including analogue sources and Microphone).
Use the REC or BSCAST buttons from the MASTER center panel of the VirtualDJ GUI to Record or Broadcast your mix.
For further Technical features and specifications, visit Rane Seventy
Product's Page
Hardware Integration Department 2020- ATOMIX PRODUCTIONS Reproduction of this manual in full or in part without written permission from Atomix Productions is prohibited.